Skip to main content

How I made article 6

This article is brought to you by Lizzsews.

Today I was scavenging around my house... looking for the right object to strike at... something that I could customize for my next make…

In today's article, I will guide you through how I spiced up a Phone stand/holder. Follow along with this project and share your result in Lizzsews Facebook group.

Recommended read: How I made article series

What I used:

  - Standardgrip mat

  - Removable vinyl

  - Transfer tape

  - Phone stand/holder

  - Lysol wipe

  - Cricut

The steps I took:


I wiped the phone stand with a Lysol wipe to create a clean and clear surface for my design. 

I decided on a charging design to use, and you can find it here on cricut design space with this image ID: #M26F6CBEC

I cut it out at 0.9” wide and kept it on uniform sizing. I cut my vinyl to the size of the design I was going to cut, but just a little bigger and placed the liner side down on the mat.

After it was cut, I weeded the design. I cut a piece of transfer tape a little bit larger than the vinyl and burnished the vinyl onto the transfer tape. 

Burnish: polish by rubbing. Smooth/scrape. 

To weed: weeding is when you remove negative pieces around a cut image.

I slowly peeled up the transfer tape, ensuring that each piece of vinyl was attached to it. 

Next was placing the transfer tape with the vinyl design onto my phone stand. I placed the design in the spot that I wanted it, using the grid lines on the transfer tape to help, and I burnished the design onto the phone stand. 

I found that this particular phone stand material was difficult to get the design to adhere to. It took quite a bit of scraping and slow peeling checks. But it turned out great in the end 😃

Recommended read: How I made article 5, TBA
Recommended read: Volleyball blanket: How I made article 7

Leave a comment below and let me know if you made this phone stand! Don't forget to subscribe to get notified for my next blog post :)


Popular posts from this blog

10 Things You Need To Start Machine Embroidery Today

 This article is brought to you by  Lizzsews . How to start machine embroidery! Here’s everything that you need to get started with machine embroidery! Without spending too much! Are you interested in sewing? Recommended read:  10 things you'll need to start sewing! 1. You are going to need an embroidery machine . You can use any embroidery machine you want. Here are a couple of examples: The Brother se600. This machine can do both sewing and embroidery, and is the best budget embroidery machine! I highly suggest this machine. The brother pe550D! This is an embroidery-only machine, with awesome Disney embroidery designs! The brother se1900. I recommend the Brother brand for sewing and embroidery machines. To note here: determine your budget, determine how much you have to spend on embroidery supplies (and blanks ) and how much you have to spend on your machine. Purchase the largest embroidery hoop that you can afford! The se600 is an amazing machine and I highly recomm

Guide To The Three Main Machine Embroidery Stabilizers

 This article is brought to you by  Lizzsews . Here is everything that you need to know about the three main machine embroidery stabilizers. Stabilizers are important in machine embroidery; they prevent puckering and support the fabric.  The stabilizer goes underneath the fabric you are embroidering. Although there are some stabilizers that will go on top of certain types of fabric, this is called a topper.  A bottom stabilizer is always needed, you can never embroider without stabilizer, but a stabilizer topper is only needed for certain blanks. The three main types of stabilizers are cutaway, tearaway, and wash away.  The first is a cutaway stabilizer. A cutaway stabilizer can be used on clothes and many different types of fabric. The cutaway stabilizer is permanent and is mainly designed for knit fabric. It is non-woven and helps get rid of pulled or sagging stitches.  The cutaway stabilizer has a lot of stretch resistance and stays intact after wearing, using, and launderin

Why Bobbin Thread Is Showing On The Top Of Your Embroidery Design

 This article is brought to you by  Lizzsews . Almost all of us have been there! Having bobbin thread show through on the top of your embroidery project is so annoying, especially when you don't know why!  Here’s a list of questions to ask yourself and how to fix them so you can prevent your bobbin thread from showing on top! Have you cleaned the race? The other day, my bobbin thread was showing on top, b efore I adjusted my tension (I always suggest to do whatever you can to fix the problem before adjusting tension) Recommended read: How to understand changing the tension on your embroidery machine Recommended read: How To Clean The Race On An Embroidery Machine I tried this neat trick, and surprisingly enough, it worked! Here’s what you do: Take a business card and use it to get the lint out from where the bobbin thread goes. You don’t want to use anything that with scratch your bobbin case.  Here’s a picture to show you how: Is your bobbin upside down?