How to cut those pesky jump stitches when machine embroidering

This article is brought to you by Lizzsews.

Jump stitches can be annoying, they're little threads in your design that are hard to cut, and you need to cut really close to the design!

There are two options for when to cut the jump stitches, you can either wait till the very end of the embroidery and cut the stitches after you take the design out of the hoop or you can cut the stitches as the machine does them.

Landscape patch embroidery design from above

Let me explain more,

1. You let the design stitch out as normal then once it’s done, take the material out of the hoop. Use small, sharp scissors and cut each thread from the starting part of the jump to the ending part of the jump. The hard part about this method is that often the jump stitches get stitched over from other stitches. This can either, a: hide the jump stitches and now you no longer need to cut them, or, b: stitch over the jump stitches in sections so that your one stitch is now two or more different sections to cut.

Recommended read: How to hoop fabrics for machine embroidery

2. After the machine completes a jump stitch, let it stitch a few reinforcement stitches, then pause the machine. Cut the stitch from the source, then cut from where it is now. Start the machine and continue the design. The problem with this method is that you need to be close to the machine, ready to cut each jump, you must pause the machine, and cutting while the hoop is in the machine is quite difficult!

- Most times a combination of these two methods works best.

- I definitely recommend small and sharp scissors, with emphasis on the sharpness of the tip of the scissors. When using the second method of cutting jump stitches, there are actually certain types of scissors with a curve to help with it. Although I still prefer to use the small scissors that came with my machine, can be seen in the picture above.

- Always cut as close to the design as possible. Remember, with machine embroidery, if the design was digitized right, there will be enough reinforcement stitches that you don’t need to worry about cutting too close.

Recommended read: How to embroider patches

Share any other methods you use or tricks you have in the comments! And don't forget to subscribe to get notified for my next blog post!

Comments

10 Things You Need To Start Machine Embroidery Today

This article is brought to you by Lizzsews . How to start machine embroidery! Here’s everything that you need to get started with machine embroidery! Without spending too much! Are you interested in sewing? Recommended read: 10 things you'll need to start sewing! 1. You are going to need an embroidery machine . You can use any embroidery machine you want. Here are a couple of examples: The Brother se600. This machine can do both sewing and embroidery, and is the best budget embroidery machine! I highly suggest this machine. The brother pe550D! This is an embroidery-only machine, with awesome Disney embroidery designs! The brother se1900. I recommend the Brother brand for sewing and embroidery machines. To note here: determine your budget, determine how much you have to spend on embroidery supplies (and blanks ) and how much you have to spend on your machine. Purchase the largest embroidery hoop that you can afford! The se600 is an amazing machine and I highly recomm

8 Reasons Why Your Upper Thread Is Shredding On Your Embroidery Machine

This article is brought to you by Lizzsews . Here are some reasons why your top thread might be shredding while you’re embroidering! Starting machine embroidery is definitely a challenge, and troubleshooting is hard. Recommended read: 10 Things you need to start machine embroidery today Often when your top thread is shredding, it’s caused by when the thread goes through the eye of the needle or while it’s going through the thread guides. 1. A dull or bent needle How long has it been since you’ve changed that needle? It might be time to swap it out! A needle only lasts about 8-10 hours of stitching, this amount of time may vary depending on what you are making. It’s good to have lots of needles on hand. Recommended read: When should I change the needle for machine embroidery 2. Are you using the right needle for the project? Are you embroidering heavier fabrics? Like denim or leather? If so, you’ll want to use a heavier needle size like 90/14. If you’re just embroidering mid-weight

Guide To The Three Main Machine Embroidery Stabilizers

This article is brought to you by Lizzsews . Here is everything that you need to know about the three main machine embroidery stabilizers. Stabilizers are important in machine embroidery; they prevent puckering and support the fabric. The stabilizer goes underneath the fabric you are embroidering. Although there are some stabilizers that will go on top of certain types of fabric, this is called a topper. A bottom stabilizer is always needed, you can never embroider without stabilizer, but a stabilizer topper is only needed for certain blanks. The three main types of stabilizers are cutaway, tearaway, and wash away. The first is a cutaway stabilizer. A cutaway stabilizer can be used on clothes and many different types of fabric. The cutaway stabilizer is permanent and is mainly designed for knit fabric. It is non-woven and helps get rid of pulled or sagging stitches. The cutaway stabilizer has a lot of stretch resistance and stays intact after wearing, using, and launderin

Lizzsews

Search This Blog