Skip to main content

How To Sew a Fleece Embroidered Patch Pillow

By Lizzsews

 This article is brought to you by Lizzsews.

Here’s how you can create a throw pillow with patching and embroidery! This is a super fun project and makes amazing gifts!

Recommended read: How to Make a Blanket Pillow

What you will need:

  • Fleece, one square of about 17” and 9 squares of 6”
  • Iron and ironing board 
  • Pins
  • Rotary cutter and cutting mat (or scissors)
  • Measuring tape
  • Embroidery thread and tear-away or cut-away stabilizer (use wash away stabilizer on top of the fleece if its thick, the fleece that I embroidered on was quite thin so I was able to get away with just tear away on the back)
  • Sewing thread
  • Machine sewing needle and machine embroidery needle
  • Baby Yoda embroidery design from Lizzsews Etsy shop
  • Stuffing 
  • Sewing and embroidery machine


The steps:


   1. Iron fleece and cut out 9 squares of 6”



   2. Hoop the stabilizer, tear-away or cutaway, I chose to use tear away. Pin (or spray) a square (colour one) to the stabilizer.

Recommended read: What is tear away stabilizer
Recommended read: How to hoop fabric for machine embroidery



   3. Select your embroidery design, thread the machine and begin the embroider!

Recommended read: How To Transfer Embroidery Designs To USB Stick To Embroidery Machine
Recommended read: How To Thread Your Sewing Machine




   4. Sew together the embroidered square (colour one) and squares of the other colour (colour two) on both sides to create a strip of three squares. Iron the strip. 



   5. Sew together two strips of three squares with colour two in the middle and colour one on the sides. Iron the strips. 


   6. Place the embroidered strip right side together with another strip and sew on the long side. Place the leftover strip right side together with the raw edge long side of the embroidered strip and sew. Iron the now square.



   7. Measure the square (or rectangle), mine ended up being 16.5” x 17.25”. Cut a square (or rectangle) of either colour one or two with these dimensions.


   8. Pin together the cut square right side together with the patched square and sew. Leaving a gap in the middle of the bottom side. I recommend making this gap as big as your four knuckles together. 



   9. Flip inside out and fill with stuffing, fill as full as you please. 

   10. Hand sew the gap and enjoy your embroidered patch pillow!





Here’s a variation you can do: use a piece of embroidered cotton in the center instead of fleece.

Kayak embroidery design

To reduce the puckering on this cotton square, I could have used cutaway instead of tearaway, hooped it more securely, used a less dense design, and a new needle.

Recommended read: How to embroider patches

Thank you for reading this article. I would love to see your creations in Lizzsew's Facebook group! Don’t forget to subscribe and leave a comment and let me know how your throw pillow went! 
Labels:

Comments

Post a Comment

Popular posts from this blog

10 Things You Need To Start Machine Embroidery Today

By Lizzsews
 This article is brought to you by  Lizzsews . How to start machine embroidery! Here’s everything that you need to get started with machine embroidery! Without spending too much! Are you interested in sewing? Recommended read:  10 things you'll need to start sewing! 1. You are going to need an embroidery machine . You can use any embroidery machine you want. Here are a couple of examples: The Brother se600. This machine can do both sewing and embroidery, and is the best budget embroidery machine! I highly suggest this machine. The brother pe550D! This is an embroidery-only machine, with awesome Disney embroidery designs! The brother se1900. I recommend the Brother brand for sewing and embroidery machines. To note here: determine your budget, determine how much you have to spend on embroidery supplies (and blanks ) and how much you have to spend on your machine. Purchase the largest embroidery hoop that you can afford! The se600 is an amazing machine and I highly recomm
5 comments
Read more

8 Reasons Why Your Upper Thread Is Shredding On Your Embroidery Machine

By Lizzsews
 This article is brought to you by  Lizzsews . Here are some reasons why your top thread might be shredding while you’re embroidering! Starting machine embroidery is definitely a challenge, and troubleshooting is hard.  Recommended read: 10 Things you need to start machine embroidery today Often when your top thread is shredding, it’s caused by when the thread goes through the eye of the needle or while it’s going through the thread guides.  1. A dull or bent needle How long has it been since you’ve changed that needle? It might be time to swap it out! A needle only lasts about 8-10 hours of stitching, this amount of time may vary depending on what you are making. It’s good to have lots of needles on hand. Recommended read: When should I change the needle for machine embroidery 2. Are you using the right needle for the project? Are you embroidering heavier fabrics? Like denim or leather? If so, you’ll want to use a heavier needle size like 90/14. If you’re just embroidering mid-weight
Post a Comment
Read more

Guide To The Three Main Machine Embroidery Stabilizers

By Lizzsews
 This article is brought to you by  Lizzsews . Here is everything that you need to know about the three main machine embroidery stabilizers. Stabilizers are important in machine embroidery; they prevent puckering and support the fabric.  The stabilizer goes underneath the fabric you are embroidering. Although there are some stabilizers that will go on top of certain types of fabric, this is called a topper.  A bottom stabilizer is always needed, you can never embroider without stabilizer, but a stabilizer topper is only needed for certain blanks. The three main types of stabilizers are cutaway, tearaway, and wash away.  The first is a cutaway stabilizer. A cutaway stabilizer can be used on clothes and many different types of fabric. The cutaway stabilizer is permanent and is mainly designed for knit fabric. It is non-woven and helps get rid of pulled or sagging stitches.  The cutaway stabilizer has a lot of stretch resistance and stays intact after wearing, using, and launderin
1 comment
Read more