Skip to main content

ImpROCKster print: How I made article 14

  This article is brought to you by Lizzsews.


In today's article, I will guide you through how 3D printed Not just any 3D print… the impROCKster print. The Rock x Among Us. Follow along with this project and share your result in Lizzsews Facebook group.

Recommended read: How I made article series


What I used:

PLA filament

ImpROCKster print file

3D printer 

Cura (slicing software)


Recommended read: What is PLA

Recommended read: About my 3D printer

Recommended read: What is slicing in the 3D printing world


The steps I took:

I started by just exploring some 3D print files. I found this awesome print from Thingiverse, created by TheRealRussell. I sliced the file in Cura and adjusted the settings. I used MECH solutions PLA filament and these were the settings that I used:


200 nozzle temp

60 bed temp

0.2mm height

50mm/sec speed

15% infill - zig zag fill

Supports yes

Retracting set as per Cura's PLA default



I printed it out, removed all of the supports and the results were great!

Recommended read: Mythosaurs 3D print: How I made article 13

Recommended read: Snow Tri-Tray: How I made article 15


Leave a comment below and let me know if you made the ImpROCKster! And don't forget to subscribe to stay up to date with all of Lizzsews new articles. See you next time!

Comments

  1. You have Shared great content here about Art Printing Toronto I am glad to discover this post as I found lots of valuable data in your article. Thanks for sharing an article like this.

    ReplyDelete
  2. Extremely useful information which you have shared here about Slm 3d Printing Nelson This is a great way to enhance knowledge for us, and also beneficial for us. Thank you for sharing a blog like this.

    ReplyDelete
  3. Great post, your all points fully clarify, Printing Company bangalore These steps are very helpful for us. Thank you for providing such a valuable information.

    ReplyDelete
  4. You've posted a phenomenal and helpful snippet of data here. I'm thankful that you basically imparted this accommodating data to us. Kindly keep on being educated thusly. Much thanks for sharing it. 3d Printing Concrete

    ReplyDelete
  5. You've posted a phenomenal and helpful snippet of data here. I'm thankful that you basically imparted this accommodating data to us. Kindly keep on being educated thusly. Much thanks for sharing it. 3d Printing Concrete

    ReplyDelete

Post a Comment

Popular posts from this blog

10 Things You Need To Start Machine Embroidery Today

 This article is brought to you by  Lizzsews . How to start machine embroidery! Here’s everything that you need to get started with machine embroidery! Without spending too much! Are you interested in sewing? Recommended read:  10 things you'll need to start sewing! 1. You are going to need an embroidery machine . You can use any embroidery machine you want. Here are a couple of examples: The Brother se600. This machine can do both sewing and embroidery, and is the best budget embroidery machine! I highly suggest this machine. The brother pe550D! This is an embroidery-only machine, with awesome Disney embroidery designs! The brother se1900. I recommend the Brother brand for sewing and embroidery machines. To note here: determine your budget, determine how much you have to spend on embroidery supplies (and blanks ) and how much you have to spend on your machine. Purchase the largest embroidery hoop that you can afford! The se600 is an amazing machine and I highly recomm

8 Reasons Why Your Upper Thread Is Shredding On Your Embroidery Machine

 This article is brought to you by  Lizzsews . Here are some reasons why your top thread might be shredding while you’re embroidering! Starting machine embroidery is definitely a challenge, and troubleshooting is hard.  Recommended read: 10 Things you need to start machine embroidery today Often when your top thread is shredding, it’s caused by when the thread goes through the eye of the needle or while it’s going through the thread guides.  1. A dull or bent needle How long has it been since you’ve changed that needle? It might be time to swap it out! A needle only lasts about 8-10 hours of stitching, this amount of time may vary depending on what you are making. It’s good to have lots of needles on hand. Recommended read: When should I change the needle for machine embroidery 2. Are you using the right needle for the project? Are you embroidering heavier fabrics? Like denim or leather? If so, you’ll want to use a heavier needle size like 90/14. If you’re just embroidering mid-weight

Guide To The Three Main Machine Embroidery Stabilizers

 This article is brought to you by  Lizzsews . Here is everything that you need to know about the three main machine embroidery stabilizers. Stabilizers are important in machine embroidery; they prevent puckering and support the fabric.  The stabilizer goes underneath the fabric you are embroidering. Although there are some stabilizers that will go on top of certain types of fabric, this is called a topper.  A bottom stabilizer is always needed, you can never embroider without stabilizer, but a stabilizer topper is only needed for certain blanks. The three main types of stabilizers are cutaway, tearaway, and wash away.  The first is a cutaway stabilizer. A cutaway stabilizer can be used on clothes and many different types of fabric. The cutaway stabilizer is permanent and is mainly designed for knit fabric. It is non-woven and helps get rid of pulled or sagging stitches.  The cutaway stabilizer has a lot of stretch resistance and stays intact after wearing, using, and launderin